|
The term "ADA Signs" has come into common use in the architectural, construction and signage industries with the advent of the Americans With Disabilities Act, or ADA. The term is sometimes misunderstood, as some people think it is synonymous with braille signs. Signs with braille and raised characters are the most visible manifestation of the law requiring access to the built environment, but the sign standards in the ADA Accessibility Guidelines, or ADAAG, require much more than just braille and raised characters on some signs. In general, almost every sign that would be considered an "architectural" sign must comply with one or another of the ADA Guidelines. In other words, if a sign identifies a permanent room or space of a facility, including exits, directs or informs about functional spaces of the facility, or identifies, directs to, or informs about accessible features of the facility, it must comply. Signs for advertising and marketing purposes, temporary signs, company logos and names are examples of signs or sections of signs that do not have to comply.〔Further Info from Image360 Signmaker's Resource Center. http://www.image360.com/Resource-Center/ADA-Requirements/〕 Although, because of the rules requiring Braille on some signs, the signage section is looked upon as benefiting persons who are blind and visually impaired, some of the sign guidelines benefit persons with mobility impairments or hearing impairments. In addition, one can say generally that easy to read and well thought out signage systems are of definite benefit to deaf people, people who have problems speaking, and people with cognitive disabilities or psychiatric conditions that cause them to avoid speaking to strangers. ==Rules== The general rules for signage covered by the law are these:〔the exact wording may be consulted on the website of the United States Access Board at http://www.access-board.gov/〕 All signs must have non-glare backgrounds and characters. (Exception is for reflective parking and other traffic signs.) Glare and reflection are a major problem for persons with vision impairments, and particularly for the elderly. All signs that contain visual characters must have a high dark to light (or vice versa) contrast between characters and their background. The important issue is not color, but lightness and darkness. Thus, a sign with very light gray letters on a charcoal gray background would be fine, but a sign with red letters on a black background would not. All signs must have "easy to read" typefaces. The rules are different for signs that identify rooms and spaces, and signs that direct and inform. That's because persons who are "functionally blind," that is, have no usable vision, are able to locate doors, and therefore can locate signs adjacent to doors that identify them, but have no consistent way to find directional and information signs that could be located anywhere along corridors. Directional and informational signs can use upper and lower case letters (recommended by many experts for visual readability) and "simple" serif typefaces of a non-decorative nature. No condensed or extended typefaces are allowed. Strokes are of medium weight, not too bold or too thin. The size of the letters is dictated by the distance of the sign from the expected position of the sign reader. Character size on these signs is to be determined by a chart in the 2010 ADA Standards for Accessible Design that uses a combination of the height of the text above the floor and the distance the reader has to stand from the sign. (ADA signs ) that identify rooms and spaces are to be located adjacent to the door they identify so they can be located by persons who are functionally blind. For the most part, one sign is used by both tactile and visual readers, so there are compromises to assist tactile readers. However, it is possible to use two separate signs with the same information. Tactile signs require uppercase characters in sans serif typefaces. (Helvetica is not required; other sans-serif typefaces can be used.) The characters can be from 5/8 inch to 2 inches high. The Braille must accompany the characters (below the characters) and must be Contracted Braille (formerly called Grade 2 Braille). The signs are installed 48 inches minimum from the baseline of the lowest raised character and 60 inches maximum from the baseline of the highest raised character. (Although the definition of "character" doesn't include Braille cells, the Access Board has stated that the 48 inch rule applies to the base of the lowest line of Braille cells.) If pictograms are used to identify the space (example: restrooms with gender pictograms), they must be in a six inch high clear field and accompanied by a tactile character and Braille label below the field. There are four symbols that stand for accessibility. One is the familiar International Symbol of Access, or "wheelchair symbol." It is used generally to show that persons with mobility impairments can access entrances, restrooms, or pathways. Three are specifically for persons with hearing impairments. The "ear" symbol is the International Symbol of Access for Hearing Loss, and is used to show the availability of an assistive listening system. The "keyboard" symbol stands for a TTY or text telephone. The "phone" symbol with sound waves stands for the availability of a volume controlled phone. 抄文引用元・出典: フリー百科事典『 ウィキペディア（Wikipedia）』 ■ウィキペディアで「ADA Signs」の詳細全文を読む スポンサード リンク
|